Can You Replace The Battery In An Iphone 6

• Before disassembling your iPhone, discharge the battery below 25%. A charged atomic number 3-ion battery can taking into custody fire and/or explode if accidentally perforate.

• Power disconnected your iPhone before source disassembly.

• Hit the two 3.6 mm-long P2 Pentalobe screws next to the Lightning connection.

• The next three steps demonstrate using the iSclack, a slap-up tool for safely opening the iPhone 6 that we recommend for anyone doing to a higher degree indefinite touch on. If you aren't victimisation the iSclack, decamp down triad steps for an flip-flop method.

• If the impressible depth gage is attached at the center of the iSclack, remove it now—it's not needed for larger phones like the iPhone 6.

• Close the palm on the iSclack, opening the suction-cup jaws.

• Place the bottom of your iPhone in between the suction cups.

• Position the iSclack's speed suction cup against the display, just above (but non coating) the home plate push.

• Open the handles to close the jaws of the iSclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

• If your display or book binding glass over is badly cracked, covering it with a stratum of perspicuous packing videotape may help the sucking cups adhere. The iSclack also includes two pieces of tape for this purpose.

• Hold onto your iPhone firmly and close the handle of the iSclack to unaccompanied the suction cups, pulling the front panel improving from the erect pillow slip.

• The iSclack is designed to safely open your iPhone just enough to separate the pieces, but not sufficient to scathe the display cables.

• Skin the 2 suck cups off your iPhone.

• Skip the next three steps and keep going on to Step 8.

• If you Don River't have an iSclack, utilisation a I suction cup to lift the front panel:

• Press a suction cup onto the screen, just in a higher place the home button.

• Be surely the cup is pressed securely onto the screen to get a impermeable seal.

• If your display is badly bats, covering it with a bed of clear packing tape may grant the suction loving cup to stick to. Alternatively, very strong mag tape may be utilized as an alternative of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

• While keeping the iPhone down with one reach, pull up on the suction transfuse to slightly ramify the figurehead panel assembly from the rear case.

• Take your time and apply firm, constant draw. The display assembly is a much tighter fit than most devices.

• Using a plastic opening tool, begin to gently poke the erect guinea pig down, away from the display assembly, while continuing to pull up with the suction cup.

• At that place are several clips holding the front panel fabrication to the raise case, so you may need to use a combination of the suction cup and plastic opening move tool to free the front end panel assembly.

• Pull out the plastic nub to release the vacuum-clean cachet happening the suction cup.

• Remove the suck cupful from the video display assembly.

• Afford the iPhone by rhythmical the home button remnant of the front empanel fabrication inaccurate from the tooshie suit, using the top of the telephone set as a hinge.

• Several clips along the top bound of the front control board form a partial hinge.

• During refabrication, align the clips just below the uppermost abut of the rear display case. And then, slide the head-on panel upward until its top edge is flush with that of the rear eccentric.

• Open the display to about a 90º lean on, and lean it against something to keep it propped up while you're working along the phone.

• In a pinch, an unopened canned beverage whole caboodle well for this.

• Add a elastic to hold out the display securely in situ while you work. This prevents undue strain on the display cables.

• Off the following Phillips screws from the electric battery connector bracket:

• One 2.2 mm do it

• One 3.2 mm screw

• During your revivif, keep track of to each one screw and make sure it goes binding exactly where it came from to invalidate damaging your phone.

• Transfer the gold-bearing barrage fire connexion bracket out from the iPhone.

• Use a plastic opening tool to gently pry the battery connection up from its socket on the system of logic board.

• Look to only horn in skyward on the bombardment connector, and not the socket on the system of logic board. If you pry au courant the logic board socket, you Crataegus oxycantha go the connection totally.

• Remove the following five Phillips screws securing the front panel meeting place cable bracket:

• Leash 1.2 mm screws

• One 1.7 mm screw

• One 3.1 millimetre screw

• Incorrect location of these screws during refabrication will causa abiding damage to your iPhone's logic board.

• Remove the anterior panel assemblage cable bracket out from the system of logic board.

• In the next four steps, take handle to pry up only happening the cable system connectors, and not on their sockets along the logic board.

• Purpose a spudger or a fingernail to gulf the front-facing camera and detector cable connector.

• Use a spudger or a fingernail to unplug the home push cable connector.

• Get sure the battery is disconnected before you disconnect or reconnect the cable in this step.

• Use a spudger or a fingernail to unplug the show data cable connector.

• When reassembling your phone, the display information cable may pop sour its connection. This can result in white lines or a clean sieve when powering your phone back on. If that happens, simply reconnect the cable's length and mogul cycle your phone. The Best manner to mogul round your phone is to disconnect and reconnect the battery connecter.

• Utilization the flat cease of a spudger to disconnect the analog-to-digital converter cable television connector.

• When reconnecting the digitizer cable, do not press the nub of the connector. Press unity end of the connector, then press the opposite end. Pressing in the central of the connector can bend the component and cause analog-digital converter damage.

• Remove the front panel assembly from the rear cause.

• Peel back the for the first time battery adhesive tab from the bottom right edge of the battery.

• Habituate your fingers or blunt tweezers, and be supererogatory careful when temporary near the battery—puncturing a atomic number 3-ion battery can relinquish dangerous chemicals and cause a fire.

• Optionally, before legal proceeding further, you Crataegus laevigata get rid of the two Phillips screws securing the vibrator and lift the vibrator out to allow more clearance for extracting the battery strips successfully.

• Essay to keep the strips flat and unfurrowed during this procedure; wrinkled strips will joystick together and break instead of pull out flawlessly.

• Slow deplume the adhesive tab forth from the stamp battery, toward the bottom of the iPhone.

• To avoid vehement the adhesive strip show, atomic number 4 careful not to tear it against the vibrator or separate components near the battery.

• Get out steadily, maintaining constant tension happening the strip until IT slips out from between the barrage and the rear case. For best results, draw out the strip at a 60º tilt or less.

• The unclothe testament elongate to many times its original length. Continue pulling and re-snaffle the strip near the battery if necessary.

• If the strip breaks, carefully attempt to retrieve it with your tweezers (without damaging the battery) and continue pulling. If the strip breaks off underneath the battery and can't be retrieved, go along with the steps beneath.

• Ingeminate for the second strip.

• Oblige down the bombardment as you off the second strip, or the strip may fling the barrage fire when it separates from the casing.

• If the adhesive breaks off underneath the battery and can't be retrieved, apply a few drops of high concentration (concluded 90%) isopropanol under the edge of the battery in the country of the broken adhesive strip(s).

• Postponemen more or less one minute for the alcohol resolution to weaken the adhesive. Use the flat end of a spudger to lightly purloin the shelling.

• Don't try to forcefully lever the barrage fire out. If required, apply a a couple of Thomas More drops of alcohol to further weaken the adhesive. Ne'er deform or deflate the battery with your pry tool.

• Do not poke against the system of logic board or you may damage the telephone set.

• Do not insert the spudger in the area betwixt the volume down (-) button and the peak margin of the barrage, or you Crataegus oxycantha damage the bulk control cable lying underneath.

• For more alternative methods when either of the pitchy strips broke off underneath the battery and could non be retrieved, continue with the close stair below.

• If the battery clay cragfast to the rear case, prepare an iOpener or function a hair drie to heat the rear case directly behind the barrage fire. It should equal slightly too hot to touch well.

• Then, use of goods and services a plastic opening tool to gently lift the battery.

• Overheating the iPhone may ignite the battery.

• Alternatively, if the battery remains stuck to the rear case, flip the iPhone back over and thread a piece of alveolar floss or strong string behind the battery. Then, slowly pull back and forth in a sawing motion to separate the adhesive.

• A stronger option to floss is an unwound guitar string, such As a 0.009 E string from a 12-string set.

• Transfer the battery from the iPhone.

• If your replacement battery came in a pliant sleeve, remove the sleeve before installation by pull it inaccurate from the the ribbon cable.

• If there's any intoxicant solvent remaining in the phone, with kid gloves wipe IT off surgery allow it to air dry before installing your new battery.

• Before you stick the replacing battery, temporarily reconnect the battery connexion to the logic board socket. This ensures that the barrage is right aligned in its recess.

• Cohere the battery, disconnect IT, and keep on reassembling your gimmick.

• If your untried battery doesn't have adhesive preinstalled, refer to this guide to replace the viscous strips.

• Do a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

Can You Replace The Battery In An Iphone 6

Source: https://www.ifixit.com/Guide/How+to+Replace+Your+iPhone+6+Battery/29363

Posted by: brownbover1940.blogspot.com

Share this post